Free Shipping for orders over $500!

ECL Reagents

3 products

  • Ultrasense Pico Western Substrate (50mlx2)

    Ultrasense Pico Western Substrate (50mlx2)

    SKU: ECL01-50

    The Ultrasense Pico Western Substrate, as a luminol-based enhanced chemiluminescent substrate, is sensitive and compatible with conducting immunoblots with horseradish peroxidase (HRP) – conjugated secondary antibodies. The low picogram to mid femtogram detection of antigen is enabled by Ultrasense Pico Ultra Western Substrate’s excellent sensitivity and long signal duration. Further, its long chemiluminescent signal duration makes both digital and film-based imaging possible without any loss of the signal. Appropriate primary and secondary antibody dilutions are suggested for attaining optimal signal intensity and duratio Features:  No optimization required. Switching to the Ultrasense Pico Western Substrate from other brands, such as Thermo Scientific™ SuperSignal™ West Dura and Millipore™ Immobilon™ substrates, does not require optimization or protocol changes. High degree of sensitivity and enhanced chemiluminescence duration. UltraSense Pico Western Substrate enables an accurate low picogram to mid femtogram detection of protein on the same immunoblot after a single exposure. Optimized for use with PVDF and nitrocellulose membranes Compatible with Western Blotting Markers Optimized for film- and CCD-based imaging. Chemiluminescent development Keep the membrane moist in the wash buffer while preparing the substrate mixture. Make sure the membrane does not dry out in the next steps. The chemiluminescent substrate solution is sufficiently stirred to prepare the 0.1ml of solution / cm2 of the membrane. For a small membrane (7 x 8.5 cm), 4 ml of solution is sufficient. For a medium-sized membrane (8.5 x 135 cm), 10 ml of solution is sufficient. Place the membrane on a clean, flat surface or in a clean container. Remove the membrane from the chemiluminescent substrate solution and drain the excess solution. Place the membrane in a plastic sheet protector or plastic wrap to prevent the film from drying out. Imaging the membrane with a digital imager or by exposure to the X-ray film. 

    $65.00

  • Ultrasense Pico Western Substrate (100mlx2)

    Ultrasense Pico Western Substrate (100mlx2)

    SKU: ECL01-100

    The Ultrasense Pico Western Substrate, as a luminol-based enhanced chemiluminescent substrate, is sensitive and compatible with conducting immunoblots with horseradish peroxidase (HRP) – conjugated secondary antibodies. The low picogram to mid femtogram detection of antigen is enabled by Ultrasense Pico Ultra Western Substrate’s excellent sensitivity and long signal duration. Further, its long chemiluminescent signal duration makes both digital and film-based imaging possible without any loss of the signal. Appropriate primary and secondary antibody dilutions are suggested for attaining optimal signal intensity and duratio Features:  No optimization required. Switching to the Ultrasense Pico Western Substrate from other brands, such as Thermo Scientific™ SuperSignal™ West Dura and Millipore™ Immobilon™ substrates, does not require optimization or protocol changes. High degree of sensitivity and enhanced chemiluminescence duration. UltraSense Pico Western Substrate enables an accurate low picogram to mid femtogram detection of protein on the same immunoblot after a single exposure. Optimized for use with PVDF and nitrocellulose membranes Compatible with Western Blotting Markers Optimized for film- and CCD-based imaging. Chemiluminescent development Keep the membrane moist in the wash buffer while preparing the substrate mixture. Make sure the membrane does not dry out in the next steps. The chemiluminescent substrate solution is sufficiently stirred to prepare the 0.1ml of solution / cm2 of the membrane. For a small membrane (7 x 8.5 cm), 4 ml of solution is sufficient. For a medium-sized membrane (8.5 x 135 cm), 10 ml of solution is sufficient. Place the membrane on a clean, flat surface or in a clean container. Remove the membrane from the chemiluminescent substrate solution and drain the excess solution. Place the membrane in a plastic sheet protector or plastic wrap to prevent the film from drying out. Imaging the membrane with a digital imager or by exposure to the X-ray film. 

    $120.00

  • 0.45µm PVDF transfer membranes for Western Blot (1 Roll)

    0.45µm PVDF transfer membranes for Western Blot (1 Roll)

    SKU: TM-PVDF45

    Cobetter PVDF transfer membranes feature high sensitivity and low background in Western blotting. The 0.45μm is suitable for most Western blotting applications and 0.2μm for immunoblotting of low MW proteins <20kDa. Specifications: Membrane Hydrophobic PVDF Pore Size 0.45 µm Thickness 125 µm Protein Binding Capacity (BSA) 135 µg/cm² Dimension 275mm x 3.75m Main Binding Mechanisms Electrostatic, Hydrophobic Pre-activation Requires ethanol (methanol) Tolerance Resistant to most organic solvents, acids and weak bases Compatibility Compatible with commonly used transfer conditions and detection methods (such as staining, chemiluminescence, radiolabeling, etc.) Storage Store the membrane flat at ambient temperature away from chemical vapors. Some solvent vapors may dissolve parts of the membrane, thereby disrupting the pore structure. Package 1 roll/pk

    $250.00

Login

Forgot your password?

Don't have an account yet?
Create account